Safety Guidelines

Health & Safety Guidelines 

Like any craft or hobby, glass working has some inherent risk of injury to the artist. As interest in lampworking has increased, it has become clear that general information on potential health and safety risks would be useful.

The following information is intended to increase your enjoyment of lampworking, while adding to your awareness and helping you reduce your exposure to potential hazards. These suggestions have been prepared and reviewed by a group of experienced lampworkers

Eye Protection 

Eye protection is very important in lampworking, for two reasons.

First, glass can sometimes shatter when placed directly in the flame, and you must protect your eyes from flying glass fragments. Goggles or glasses with side shields are good for this.

You must also protect your eyes from potentially damaging Ultraviolet and Infrared rays, which are emitted when you melt glass in a flame. For many years, the standard eye protection for lampworkers has been “didymium” glasses, which have the additional feature of filtering out the distracting yellow glare given off by molten glass.

In recent years other types of protective eyewear have become available, some of which are superior to traditional didymium glasses. The type of protective eyewear that is right for you depends on the type of glasswork you will be doing. For instance, making beads would give off less radiation than working a large piece of borosilicate tubing, which in turn gives off less than melting fused quartz. Also, different people may have different sensitivity.

Please protect your eyes. Check with your supplier and other reliable sources for more information on choosing eye protection.

Respiratory Hazards 

Melting glass in a flame produces a number of gasses and vapors that can affect your health. It is important, therefore, to ventilate your work area. At the very least, you should provide “dilution ventilation”, in which a steady stream of air flows across your work area, drawing any vapors or gasses away from your face and out of the room. Windows at opposite ends of your work area, one of which has an exhaust fan, can be an effective form of dilution ventilation.

Some lampworking operations may require “local exhaust ventilation,” such as a fume hood, to eliminate hazardous or irritating vapors and gasses. If you find that you feel slightly short of breath or that you have a headache at the end of a work session, then you can be certain your ventilation is inadequate.

An additional respiratory hazard is posed by glass dust particles you might encounter in your studio or work area. These include powdered “bead release” compounds, the dust stirred up when you work with vermiculite and loose particles of refractory materials such as brick or ceramic-fiber insulation inside your kiln.

Take care not to inhale these irritating and potentially harmful dust particles. Wear a respirator if necessary to reduce your exposure. Be aware of hazardous dusts that can be stirred up when you are cleaning your studio. You can also use a wet/dry shop vacuum to pick up glass particles or use a sweeping compound made for fine particulates, in order to keep the glass dust from rising up off the ground.

Wet down any questionable areas or spills with a spray bottle before wiping with a wet rag, to reduce the chances of inhaling particles. If you sandblast your finished pieces, follow all safety guidelines appropriate to sandblasting.

Cuts and Burns 

These can be avoided with common sense and care. The most common minor burns occur when someone picks up the end of a glass rod or tube, forgetting that it is hot. A simple system, such as always laying the hot end of a rod away from you, can help you remember which end to grab.

Arrange your work area so that you never have to reach in front of your torch to get a tool or piece of glass. Choose your work clothes carefully, avoiding synthetic fibers, long loose sleeves, and shirts with open pockets or pants with folded cuffs.

Burns can be treated with ice, aloe vera sap, cold cider vinegar, or a variety of home remedies. Treat your injuries with respect; serious cuts or burns may require professional medical attention.

Tanks and Torch 

Potential hazards also exist any time you work with compressed gasses. Carefully follow any manufacturer’s instructions that come with your regulators or gas tanks and check with your suppliers for safe operating procedures.

Never move oxygen tanks without their protective cap in place. If the tank falls over, the valve stem can be sheared off by impacting against a table or other object. The pressure inside the tank may then be high enough to send the cylinder flying like a rocket, injuring you and damaging your building.

Oxygen tanks should be either laid on their side and secured to prevent rolling, or chained securely to a wall so they don’t fall over. Note also that oxygen regulators, hoses and fittings should never come into contact with grease or oil, which can ignite spontaneously in the presence of pure O2. 9

Be sure to install check valves and flashback regulators on your fuel, gas and oxygen regulators to prevent backwards flow of gasses-a major hazard in the event of a fire or torch malfunction. 

Make sure that your torch is secured to the work surface so that it doesn’t move if a hose is yanked. Keep all flammable and combustible materials well away from your torch.

At the end of each work/play day, shut off your oxygen and gas tanks and bleed the pressure out of the lines by opening your torch valves.

Other Hazards 

These can include muscle strains or other injuries from maneuvering heavy oxygen tanks or repetitive movements (such as making hundreds of beads). Take frequent breaks and pay attention to your body’s signals to minimize these types of injuries. Check for accurate height of table to chair for comfortable work.

Dehydration and heat exhaustion are other possible hazards to watch out for. Drink plenty of water, especially if you are working with a large flame. You may also consider applying a sunscreen to your skin to protect it from the radiation given off by the flame.

The following references may be useful in protecting yourself from the common hazards of lampworking:

ArtisBeware, by Michael McCann, available from Center for Safety in the Arts, 5 Beekerman St., Ste. 280, New York, NY 10038

Contemporar Lampworking,  A Practica Guide  to Shaping  Glas I the Flame  by Bandhu  Scott  Dunham,  available  from  Salusa Glassworks, P.O. Box 2354, Prescott, AZ 86302

Glassblowing: An Introduction to Solid and Blown Glass Sculpturing by Homer L. Hoyt, Crafts & Arts Publishing Co. Inc, 626 Moss St., Golden, CO 80401

The Artists Complete Health and Safety Guide by Monona Rossol, available from Allworth Press

VentilationA Practical Guide for Artists, Craftspeople and Others in the Arts by Nancy Clark, Thomas Cutter and Jean Ann McGrane, available from Center for Safety in the Arts

Beads from the Beginning by Brian Kerkvliet, Glass Art Magazine, November/December 1994, P.O. Box 260377, Highlands Ranch, CO 80126

F.Y. Eyes by Lisa M. Malchow, Fusion Journal of the American Scientific Glassblowers Society, May 1993. 1507 Hagley Rd., Toledo, OH 43612

Glassmaking Health anSafety by Monona Rossol, Glass Art Society Technical Journal, 1989. Reprint available from Allworth Press

Optical Radiation Hazards in Glassblowing by Gary E. Myers, Fusion Journal of the American Scientific Glassblowers Society, August 1976

This information is offered as a starting point for your own safety research, and new information may affect the appropriateness of thesrecommendations. The suppliers of this information assume no liability for any injury or harm which may result from use or misuse of this

recommendations. The suppliers of this information assume no liability for any injury or harm which may result from use o

information. Be sure to consult with your supplier, physician, or other qualified expert regarding any safety questions you have.